GPS ANTENNA 3M LENGTH FOR ARDUINO

GPA Antenna used to received a signal from satellite. This antenna is needed to place at open area workplace. This is because GPS have an unit typically which is will NOT WORKS indoor, underwater or underground.

The picture show that the GPS Antenna for Arduino GPS Shield cable lenght 3M.

So, the combination of GPS Shield + GPS Antenna 3M length for Arduino Uno is shown below:

GPS SHIELD ARDUINO V3.0

Arduino GPS shield is a GPS module bread out broad designed for Global Positioning System receiver with SD interface. It is easy to use for recording the position data into SD card.

The figure show that the chip of the GPS Shield Arduino V3.0.

The features of this GPS Shield Antenna:

• with micro SD interface
• active antenna design with high receive sensitivity, compatible normal antenna
• extremely fast time to first fix at low signal level
• UART interface
• Operation tem perature just nice. (-40deg ~+85deg)

RESULT & ANALYSIS (GPSSCREEN)

The coding blinking has been download to my Arduino Uno Board. The Figure above shown that the led is blinking.

To download any coding to Arduino controller, here is the step has to follow:

1. Compile the coding
2. Download
3. Conclusion

• Here is the compile session.

As in figure above, after finish the coding, we need to click the right symbol (√). Then it will compiling the coding and check whether the code.

Any error of the code will be display at the black screen. After the compiling is finished , it will display as picture shown below.

• Here is the second step is download.

To download the coding, first. Click the (->) symbol ad shown in figure above. Then, wait for device to downloading.

After the downloading is finished, it will shown like the figure below:

Now, the coding has been downloaded to the Arduino Uno board. Lastly, the project is in progress to develop.

ARDUINO UNO'S SOFTWARE PROGRAMMING (GPSSCREEN)

The objective of this programming is to understand , investigate and recognize the input and output of pin. This is all about Arduino Uno controller.

So, as my task, I need to review this programming. Review in studying and understanding the basic examples of Arduino coding of the Arduino Uno's software programming.

As figure above, is the programming of the Arduino where can be download here ;  http://www.arduino.cc/ . The software is freeware.

From the two figures above, it is Arduino Pin Mapping. The supply for the controller is around 

7-12V DC. The board has 28 pin-outs. All the pin-out for the board we can see above.

DEMONSTRATION MODEL

Base on the objective of my project is to apply system in car alarm security. So, I need to buy the demonstration model to implement the technology that use to generate a new knowledge about how to secure the car or 'any vehicles".

As usual, the system that I applied or used in car is to programmed the Arduino micro controlled by IDE (Integrated Development Engineering) on version c++.

The demonstration model that I used is car under the model of  BMW 645Ci.

The prove of purchase of car model is below.

THE FIRST TRYING AND EARLIER RESULT

The first and earlier result that can be showed by this security alarm and GPS coordinate using Arduino is shown below.

The result of Arduino GPS and GPS data longger showed there is no signal detection at current location. This case may be happened caused of GPS antenna cannot received a signal from satellite.

The principle of GPS state that the GPS typically will not works indoor, underwater or underground. There is no signal if the GPS was located in a building and so on.

This case absolutely relate with GPS standard. To make sure a measurement of GPS, the open areas are needed in order to get an accurate of GPS data.

ARDUINO GPS CONFIGURATION PART II

GPS Screen for Latitude and Longitude location.

The function of GPS Shield for Arduino used to produce a GPS data, to store the data through SD card and find out the location detected. Futhermore, The Arduino Uno will support the features of GPS Shield in order to pointed out the result of the project.

The GPS Screen configuration are here:

The conclusion that I can made from this GPS configuration is FAILED current to the technical problem. The result is showed above where is no detection of location and trying to get real data.

I will re-test and re-trying for the next solution to find the current location detection.